A Simple Sprinkler Spruce-Up Could Save 25,000 Gallons of Water!

0

Temperatures are rising and lawns and gardens are starting to turn green again, which means we’re entering sprinkler season. But did you know that homes with timer-controlled irrigation systems use about 50 percent more water outdoors than homes without irrigation systems?

When it comes to a home’s irrigation system, a little maintenance goes a long way. The EPA estimates that “a household with an automatic landscape irrigation system that isn’t properly maintained and operated can waste up to 25,000 gallons of water annually.”

It’s easy to see why it’s crucial to ensure sprinkler systems are programmed correctly; that sprinkler heads are all pointed in the right direction; and that leaks are repaired. It’s also important to water only when your lawn or garden needs it.

A good Sprinkler Spruce-Up is just the ticket to help ensure you’re not wasting water (or money!) this growing season. To get started, check out the tips below, all from the EPA’s WaterSense Sprinkler Spruce-Up program. (And for more tips on saving water in the lawn and garden, check out our post Watering Properly is Key to Healthy Plants — and Conservation):

Inspect For Breaks and Leaks

Missing or broken sprinkler heads can be hard to find because most irrigation systems run overnight or early in the morning. Running an irrigation system with broken and damaged sprinkler heads can cause overflowing and flooding of water on the landscape.

WaterSense has a downloadable checklist to help you walk through each zone of your irrigation system and inspect for signs of water waste:

  • Look for heads that do not pop up fully or are tilted as they can unexpectedly spray to the wrong areas.
  • If you find a broken head, place a flag next to the broken sprinkler so you will be able to work on it later. You may be able to fix broken heads yourself, but if you are unsure, go with a pro — notify an irrigation professional certified by a WaterSense labeled program, and they can replace your broken sprinkler heads.

 

A whimsical graphic of a water droplet holding a hose, with the words "Connect hoses and pipes to reduce leaks," for a post about Sprinkler System Tune-ups from Lehigh County Authority.Connect Sprinklers, Pipes, and Valves

Leaks can occur at the joints between sprinklers and the piping. Leaking joints can also be a sign of too much water pressure or particles in the water. Check that your pressure regulator is installed properly. For other tips on identifying and fixing leaks, check out our Fix-a-Leak Week campaign!

Between irrigation cycles, look for areas of the landscape with water pooling on the surface; that could be a sign of an underground leak. Check the connections inside valve boxes to make sure all the valves and other components are securely connected and that the valves can shut. If the valves are not able to close completely, your system could slowly seep water even when it is turned off.

 

 

 

 

 

Direct Sprinklers For Best Water Coverage

Are you watering the driveway, house, or sidewalk instead of your yard? Irrigation water that lands on hardscapes goes to the stormwater drain instead of the landscape. Any sprinklers that are spraying onto driveways, sidewalks, or walls should be turned toward the landscape. The sprinkler can be adjusted to as wide or as narrow as necessary.

For best results:

  • Each sprinkler should be able to reach the sprinkler head next to it, known as head-to-head coverage.
  • Make sure to properly direct sprinkler for uniform coverage to avoid dry spots in the landscape.
  • Avoid overspraying or misting due to high pressure. Consider installing spray sprinkler bodies with integral pressure regulation which maintain consistent water pressure so that nozzles can operate efficiently.

 

Select a WaterSense Labeled Irrigation Controller

A whimsical illsutration of two water droplets as one buys a WaterSense controller, for a blog on Sprinkler Spruce-Ups for Lehigh County Authority.A WaterSense labeled irrigation controller uses local weather and landscape conditions to automatically adjust your irrigation schedule based on your location, size of your landscape, and scheduled days to irrigate. Irrigation controllers have intuitive programming controls to schedule irrigation based on the plant water requirement.

If you notice that runoff occurs when you run your irrigation system long enough to meet the plant water requirement, consider breaking up the irrigation into smaller intervals. Short intervals of irrigation with breaks in between to allow the water to seep into the soil is called cycle-and-soak. Cycle-and-soak promotes deeper watering and deeper root growth of the plants.